W M 3 FOR TYPICAL REMOTE CONTROL DETAILS, SEE DOCUMENT CIRCUIT DRAWN WITH POWER SUPPLY OFF 2 V 2 1 3 4 U 3 PHASE SUPPLY RWS100 1 3 6 5 U V TRANSFORMER TAPPING OPTIONS Tap E W FS1 C1 W X Y Z C2 W U X Y Z Nominal 50/60Hz TYPE 1 220/230 380/400 400,415/420 440/460 FUSE FS1=250mA ANTI-SURGE PS1 W X Y Z 120VAC 4 _ 0VDC 3 24VDC 6 + TRANSISTOR SWITCHING FOR 24VDC CONTACTORS (IQ10-35) RELAYS ONLY FITTED WHEN 120VAC CONTACTOR IS FITTED FOR IQ40,70,90,91 & 95 SK2 0VAC 1 4 24VDC NOMINAL SUPPLY (OUTPUT) 5 FUSE FS1=250mA ANTI-SURGE SK14 0VDC 1 24VDC X Y 2 REFER TO SHEET 2 FOR NOTES & OPTION PCB'S IF FITTED 26 WAY SK13 6 TORQUE SENSOR POSITION SENSOR MONITOR RELAY 3 4 3 2 1 2 10 WAY FS2 (IF FITTED) 100mA MAKE AT FULLY SHUT MAKE AT FULLY OPEN SK9 BREAK AT FULLY SHUT 4 - BATTERY 1 + SK14 1 5 SK8 BREAK AT FULLY OPEN S1 S2 S3 S4 18 WAY CLOSED OPEN REMOTE STOP 42 43 44 6 7 8 2 8 9 7 3 10 11 6 4 12 13 5 33 34 10 STOP/ MAINTAIN SK6 SK7 1 SK4 9 CLOSE 50% TYPE 3 660/660-690 690/- FUSE FS1=150mA ANTI-SURGE SK13 SK3 TYPE 2 346/380 480/500 240/240 550/575 OPEN 8 COMMON -VE 1 ESD 12 OPEN INTERLOCK 13 CLOSE INTERLOCK 14 COMMON -VE 5 35 36 25 37 LOCAL SK1 SLOT A Iss Date Chkd Revision Details 5 090113 PMJ Re-track of the 24V DC pin of SK14 to behind the diode. 6 060614 PMJ 400v added to type 1 tapping Y. Note added to sheet 2 note 1. www. 38 31 SK2 SLOT B .com IQ BASIC DIAGRAM ROTORK CONTROLS LTD ROTORK CONTROLS INC Drawn by: PMJ Date : 160512 BATH, BA1 3JQ ROCHESTER Base WD: 100B0000 ENGLAND NY 14624, USA Tel:01225-733200 Tel:585-247-2304 Job No : - MI No : - - Circuit Diagram Number 100B0000 B1 C1 B2 C2 Issue No 6 Sheet 1 of 2 IQ3 CIRCUIT DRAWN WITH POWER SUPPLY OFF NO OPTIONS FITTED NOTES 1.FUSES: -PS1 is a self-resetting fuse. -Refer to publication PUB002-039 for approved fuses FS1 and FS2. -Actuator rated voltage specified on nameplate. Voltage tolerance +/-10%, applies for rated torque performance; duty cycle is not gauaranteed. 2.REMOTE CONTROL: -For typical remote control circuits refer to: -RWS indicated or PUB002-041. -For DC and AC control, connect –ve/0V to terminal 36. -(For negative switch / positive common, refer to RWS indicated). -Control signal threshold voltages: -DC: “on” ≥16Vdc / “off” ≤8Vdc, max 60Vdc. -AC: “on” ≥60Vac / “off” ≤40Vac, max 120Vac. -Control signal duration to be 300ms minimum. -Maximum current drawn from remote control signals is: -8mA at 24Vdc or 12mA at 120Vac. -Supply provided on terminals 4 & 5: -Intended for remote control. -Max external load 5W at 24Vdc / 5VA at 120Vac 3.INDICATION: -For typical position, status and alarm indication see PUB002-041. -“S” contacts are user configurable and are shown in their default setting. -Refer to PUB002-040 for functions and configuration instructions. -Monitor Relay indicates actuator availability for remote control (shown “unavailable”). It can be configured to exclude local/remote selection. -Refer to PUB002-040 for monitored functions and configuration instructions. -Voltage applied to indication contacts must not exceed 150Vac -Individual Switch current must not exceed 3.5A inductive, 5A resistive and no more than 8A in total for all 4 contacts. 4.BATTERY: -Battery maintains local and remote “S” contact indication only. -Refer to installation manual for approved replacement battery types. See Sheet 1 for all Revision details/information Circuit Diagram Number Issue No 100B0000 6 Sheet 2 of 2 IQ3
